My main question is:
How to bind my ppp0 interface connection (from Mobile Broadband ZTE AC782) into my OpenVPN connection (from vpngate.net config file)?
In short words:
I want to hide my IP on all applications by VPN but I only can not do it if I connected via ppp0.
My case is:
- My IP address is still detected by http://whatismyip.com as my ISP's IP (Indonesia) not another country specified in config file after I start
sudo openvpn --config the_config_file.ovpn. - As a comparison, when I connect to the internet via wlan0 (any wifi hotspot), my command
sudo openvpn --config the_config_file.ovpnalways bind wlan0 interface and my IP address detected as another country according to the OpenVPN config file. - In short, my OpenVPN can not "wrap" ppp0 interface.
My workaround:
- I read and tried what this tutorial explained. But my IP is still detected as my ISP's IP.
- I read and tried binding address by parameter -local from this tutorial, but it is same.
- I read and tried this tutorial to force any connection to whatismyip.com to pass through tun0, but bash says "tun0: Unknown host".
My networking conditions:
I connected into the internet via wvdial.
ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:414 errors:0 dropped:0 overruns:0 frame:0
TX packets:414 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:30204 (30.2 KB) TX bytes:30204 (30.2 KB)
ppp0 Link encap:Point-to-Point Protocol
inet addr:10.253.192.118 P-t-P:10.20.31.22 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:17543 errors:0 dropped:0 overruns:0 frame:0
TX packets:18431 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:11671986 (11.6 MB) TX bytes:2174511 (2.1 MB)
tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:10.211.1.13 P-t-P:10.211.1.14 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:23 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:7270 (7.2 KB) TX bytes:0 (0.0 B)
ip rule show
0: from all lookup local
32764: from all to 10.253.192.118 lookup admin
32765: from 10.253.192.118 lookup admin
32766: from all lookup main
32767: from all lookup default
ip route list
default dev ppp0 scope link
10.20.31.22 dev ppp0 proto kernel scope link src 10.253.192.118
10.211.1.14 dev tun0 proto kernel scope link src 10.211.1.13
wvdial:
--> WvDial: Internet dialer version 1.61
--> Cannot set information for serial port.
--> Initializing modem.
--> Sending: ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATDT#777
--> Waiting for carrier.
ATDT#777
CONNECT 3100000
--> Carrier detected. Starting PPP immediately.
--> Starting pppd at Sat Jan 31 13:23:59 2015
--> Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
--> --> PAP (Password Authentication Protocol) may be flaky.
--> Warning: Could not modify /etc/ppp/chap-secrets: Permission denied
--> --> CHAP (Challenge Handshake) may be flaky.
--> Pid of pppd: 4591
--> Using interface ppp0
--> pppd: p8�[08]8@�[08]
--> pppd: p8�[08]8@�[08]
--> pppd: p8�[08]8@�[08]
--> pppd: p8�[08]8@�[08]
--> local IP address 10.253.192.118
--> pppd: p8�[08]8@�[08]
--> remote IP address 10.20.31.22
--> pppd: p8�[08]8@�[08]
--> primary DNS address 10.17.118.187
--> pppd: p8�[08]8@�[08]
--> secondary DNS address 10.17.118.251
--> pppd: p8�[08]8@�[08]
Is there any workaround for to so my ppp0 connection can go trough VPN? What is the technique name of this problem? Routing? I am sorry I know nothing about networking. Thank you very much.
