up vote 3 down vote favorite

I tried to install Ubuntu 12.04 on a Intel NUC D54250WYK.

Install went well, but after the reboot, I have the following message from the Intel boot agent:

Media test failure, check cable
Exiting Intel boot agent
Reboot and select proper boot device
or insert boot media in selected boot device

Went to setup, selected the ssd as primary boot device, but same result.

Is there a complete guide to install ubuntu on a Nuc haswell?

Any help would be appreciated!

share|improve this question
up vote 1 down vote accepted

Move the yellow jumper for the BIOS to the next setting along and disable UEFI boot leaving the Legacy piece in place

You'll need the linux drivers from Intel and moprobe the kernel to get wired internet working.

Audio will not work over HDMI without a kernel > 3.10, so you may want to update the default one

share|improve this answer
1  
Thanks, but it finally installed well, I just repeated the install and everything works, except the WIFI (Intel Centrino N6235), it works but connexion speed is about 6x slower than with an android phone tethered to the NUC. To solve this do I need to install Intel drivers and firmware updates for the NUC, or the Intel Linux drivers for the wifi card, or both ? (Or is it just this model of wifi card that gives bad reception ?) – Gonzague Dec 27 '13 at 14:06
    
Edit: Sleep mode does not work too, it wakes up 2 seconds later. – Gonzague Dec 27 '13 at 23:48
up vote 2 down vote

Check out this article: http://arstechnica.com/gadgets/2014/02/linux-on-the-nuc-using-ubuntu-mint-fedora-and-the-steamos-beta/

They recommend renaming the EFI file to /mnt/EFI/BOOT/bootx64.efi.

share|improve this answer
up vote 2 down vote

I recommend to update the BIOS with intels latest BIOS-version first. I didn't had any problems to install 14.04 on my D54250WYK. They fixed their problems.

share|improve this answer
    
This worked great. I had the problem, updated the bios, and then ubuntu popped up. – murtuza Sep 23 '14 at 2:26
up vote 1 down vote

I spent about a day unsuccessfully trying to install Ubuntu 13.10/12.04 in both UEFI and legacy BIOS mode. In UEFI mode, the hard drive is not detected and in legacy mode, the kernel hangs. I figured regardless of whether UEFI or legacy mode is used, there's going to be an extra step involved, so I decided to stick with UEFI mode.

The following link should help:

https://help.ubuntu.com/community/UEFI

Basically, I followed the web page and left Fast Boot and Intel Smart Response Technology disabled. The system booted the LiveUSB drive with secure boot enabled. Also, ensure that UEFI is checked/enabled in BIOS. Then install Ubuntu in UEFI mode (website has information on how to identify whether LiveUSB is booted with legacy or UEFI mode). After install, reboot using the LiveUSB drive and select "Try Ubuntu". Follow the instructions in the section, "Converting Ubuntu into EFI mode" to download/install the Boot-Repair utility and use it to separate the /boot/efi partition. Afterwards, the UEFI firmware was able to detect and boot Ubuntu 13.10 from the mSATA drive.

share|improve this answer
    
How is your network ? Do you use a wifi card ? Do you have full speed ? – Gonzague Dec 28 '13 at 23:13
    
I'm also using the Intel Centrino Advanced-N 6235. My router is G capable of 54Mb/s. My system is connected at 54Mb/s. My network seems to work fine. – user229649 Dec 29 '13 at 0:22
    
Do you have any issue with sleep mode ? – Gonzague Dec 29 '13 at 8:40

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.