How do I get the CPU temperature?

Question

How do I get the CPU temperature?

Answer 1

Install lm-sensors

sudo apt-get install lm-sensors 

After installation type the following in terminal

sudo sensors-detect

You may also need to run

sudo service kmod start

It will ask you few questions. Answer Yes for all of them. Finally to get your CPU temperature type sensors in your terminal.

sensors

Output:

$ sensors
coretemp-isa-0000
Adapter: ISA adapter
Core 0:      +41.0°C  (high = +78.0°C, crit = +100.0°C)  

coretemp-isa-0001
Adapter: ISA adapter
Core 1:      +41.0°C  (high = +78.0°C, crit = +100.0°C)  

w83627dhg-isa-0290
Adapter: ISA adapter
Vcore:       +1.10 V  (min =  +0.00 V, max =  +1.74 V)   
in1:         +1.60 V  (min =  +1.68 V, max =  +1.44 V)   ALARM
AVCC:        +3.30 V  (min =  +2.98 V, max =  +3.63 V)   
VCC:         +3.28 V  (min =  +2.98 V, max =  +3.63 V)   
in4:         +1.85 V  (min =  +1.66 V, max =  +1.11 V)   ALARM
in5:         +1.26 V  (min =  +1.72 V, max =  +0.43 V)   ALARM
in6:         +0.09 V  (min =  +1.75 V, max =  +0.62 V)   ALARM
3VSB:        +3.30 V  (min =  +2.98 V, max =  +3.63 V)   
Vbat:        +3.18 V  (min =  +2.70 V, max =  +3.30 V)   
fan1:          0 RPM  (min = 10546 RPM, div = 128)  ALARM
fan2:        892 RPM  (min = 2136 RPM, div = 8)  ALARM
fan3:          0 RPM  (min = 10546 RPM, div = 128)  ALARM
fan4:          0 RPM  (min = 10546 RPM, div = 128)  ALARM
fan5:          0 RPM  (min = 10546 RPM, div = 128)  ALARM
temp1:       +36.0°C  (high = +63.0°C, hyst = +55.0°C)  sensor = diode
temp2:       +39.5°C  (high = +80.0°C, hyst = +75.0°C)  sensor = diode
temp3:      +119.0°C  (high = +80.0°C, hyst = +75.0°C)  ALARM  sensor = thermistor
cpu0_vid:   +2.050 V

To see HDD temperature Install hddtemp

sudo apt-get install hddtemp

Output:

$ sudo hddtemp /dev/sda        
/dev/sda: ST3160813AS: 34°C

Answer 2

Quick command-line solution; shows temperature in millidegrees Celsius (m°C)

cat /sys/class/thermal/thermal_zone*/temp

Applet

If you are looking for a easier-to-access version, add a Hardware Sensors Monitor to Gnome-Panel:

1. sudo apt-get install sensors-applet - this will install the sensors-applet package

2. Right-click the panel, select Add to panel..., then select this:

3. You're done. You can configure which sensors are displayed by right-clicking the applet and selecting Preferences->Sensors.

   

Answer 3

A good indicator for monitoring temperature, fan speeds and voltage is psensor. It shows output of all sensors, draws graphs. Also selected outputs can be placed in indicator panel.

It can be installed from Ubuntu repositories by typing:

sudo apt-get install psensor

Newer versions of psensor can be installed from ppa:

sudo add-apt-repository ppa:jfi/ppa
sudo apt-get update
sudo apt-get install psensor

It can also draw graphs when you tick the boxes in the graph column:

Here is some information with more pictures.

Another useful link

In some cases not all sensors are displayed. Then you can run

sudo sensors-detect

and answer "yes" to all questions. But is not quite safe in some cases, but I never had any real problems with that. A safer way is to take default answers.

Some additional sensors may appear.

Answer 4

Temperature without third-party apps

At the time of writing, all the answers involve use of third-party utilities. If you want to find out the temperature without installing anything, use:

$ cat /sys/class/thermal/thermal_zone*/temp
20000
53000
50000
53000
56000
68000
49000
50000

To see what zones the temperatures are referring to use:

$ paste <(cat /sys/class/thermal/thermal_zone*/type) <(cat /sys/class/thermal/thermal_zone*/temp) | column -s $'\t' -t | sed 's/\(.\)..$/.\1°C/'
INT3400 Thermal  20.0°C
SEN1             45.0°C
SEN2             51.0°C
SEN3             57.0°C
SEN4             59.0°C
pch_skylake      77.5°C
B0D4             50.0°C
x86_pkg_temp     51.0°C

The temperatures are stored in Celsius with 3 implied decimal places. sed is used to "prettify" output.

The last temperature is x86_pkg_temp reported at 54.0°C. For the Skylake i7 6700HQ CPU, I used this temperature for Conky display below.

Temperature with Conky

If you don't mind third-party utilities I like to use Conky--a light weight system monitor.

Conky commands

Within conky the system variable I used to monitor an Ivy Bridge CPU is:

${hwmon 2 temp 1}°C

To monitor a Skylake CPU I used:

${hwmon 0 temp 1}°C

Conky display

The conky display looks like this:

The temperature starts at 72°C with a single CPU running at 100% in turbo mode of 3200 MHz. Then turbo is switched off and temp drops 10°C to 62°C with a non-turbo speed of 2600 MHz. 10 seconds later turbo is turned back on and temperatures immediately spike back up to 72°C.

---

Controlling Temperature

After knowing your temperature you probably want to control it better. tlp works wonders for keeping system under control. It works with thermald, Intel Powerclamp, Battery vs AC for USB power, etc. Although highly configurable I've never had to change the configuration settings for a pleasant Out-Of-The-Box experience. Prior to using it I had all kinds of problems with an IvyBridge laptop overheating all the time. I have it on my new Skylake laptop and the fans NEVER run except when doing Ubuntu 16.04 LTS to 18.04 upgrade.

You can get a very detailed write-up with installation instructions here: Stop cpu from overheating

Answer 5

hardinfo is very useful tools to get all hardware information.

Install hard info by sudo apt-get install hardinfo. Then you can get temperature by sensors.

Answer 6

1. install the small package of acpi by this command

   sudo apt-get install acpi
   

2. You will need to press Y for confirmation for the first time. Now to find temperature type this command

   acpi -t
   

Answer 7

After you install lm-sensors:

sudo apt install lm-sensors

run:

sudo sensors-detect

you can run the following command to view hardware temps:

watch -n 1 sensors

Also, the fan is usually controled by BIOS.

---

Another good tool is i7z for Intel Core processors:

sudo apt install i7z
sudo i7z

and because i7z runs like top, there is no need to use watch.

Answer 8

XSensors

XSensors reads data from the libsensors library regarding hardware health such as temperature, voltage and fan speed and displays the information in a digital read-out.

Open the terminal and type:

sudo apt-get install xsensors lm-sensors

Then detect your computer's hardware sensors by opening the terminal and running the command:

sudo sensors-detect

Then you will get asked a lot of questions about what hardware you want the program to detect. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing.

Xsensors vs. Psensor

XSensors and Psensor both monitor the computer's temperature and the fan speeds. The difference between the two applications is in the level of detail of the information that is displayed and how the information is displayed.

XSensors displays a little bit more specific information than Psensor. Psensor is smaller and more unobtrusive than XSensors and it displays itself on the desktop as a little thermometer icon in the notification area in the upper right corner of the desktop. You can right-click the thermometer icon at any time to display the hardware temperatures.

Setting up Psensor to detect your computer's hardware is done the same way as Xsensors, by installing lm-sensors to detect your computer's hardware sensors. Then detect your computer's hardware sensors running the command:

sudo sensors-detect  

and as with Xsensors, accept the default answers to all questions.

In Ubuntu 16.04 and later Psensor detects your computer's hardware sensors automatically without running sudo sensors-detect

Answer 9

On Raspberry Pi, you can retrieve the temperatureusing vcgencmd:

vcgencmd measure_temp

Output:

temp=39.0'C

Answer 10

Just so you guys know, none of this install junk like sensors are needed. Just do an acpi -V and BOOM, you got everything. Example:

Battery 0: Charging, 91%, 00:17:25 until charged
Battery 0: design capacity 3310 mAh, last full capacity 3309 mAh = 99%
Adapter 0: on-line
Thermal 0: ok, 40.0 degrees C
Thermal 0: trip point 0 switches to mode critical at temperature 127.0 degrees C
Thermal 0: trip point 1 switches to mode hot at temperature 127.0 degrees C
Cooling 0: pkg-temp-0 no state information available
Cooling 1: LCD 0 of 100
Cooling 2: Processor 0 of 10
Cooling 3: Processor 0 of 10
Cooling 4: Processor 0 of 10
Cooling 5: Processor 0 of 10

WAY easier than installing all of this and kmod... Just do acpi -V.

Answer 11

If you like Python, you can use psutil.

>>> import psutil
>>> psutil.sensors_temperatures()['coretemp']
[shwtemp(label='Physical id 0', current=67.0, high=100.0, critical=100.0), shwtemp(label='Core 0', current=67.0, high=100.0, critical=100.0), shwtemp(label='Core 1', current=65.0, high=100.0, critical=100.0)]

... will do the job. With a little coding, you can for example obtain the Temp vs CPU of your system.

It's convenient to update psutil by issuing sudo pip3 install psutil --upgrade.

Answer 12

All bash:

getTemp () {
  for zone in `ls /sys/class/thermal/ | grep thermal_zone`
  do
    echo -n "`cat /sys/class/thermal/$zone/type`: "
    echo `cat /sys/class/thermal/$zone/temp | sed 's/\(.\)..$/.\1°C/'`
  done
}

getProcesses() {
  top -b -n 1 | head -n 12  | tail -n 6
}

update () {
  while :
  do
    clear
    getTemp
    echo -e "\nTop 5 CPU hogs:"
    getProcesses
    sleep 5
  done
}


update

Answer 13

/sys/class/thermal/thermal_zone0/temp

this file holds cpu temperature. So, you can make a script named temp and move it to /bin then in terminal enter temp.

My temp file looks like -

 #!/bin/bash
 cpu_temp=$(< /sys/class/thermal/thermal_zone0/temp)
 cpu_temp=$(($cpu_temp/1000))
 echo $cpu_temp°C

my answer is modified of www.cyberciti.biz

Answer 14

And here's my 2-cents on this matter. There's tmon, a very simple tool that reads the temperature while running another process, just like time, watch, timeout, etc... tmon is a thin wrapper around /sys/class/thermal/thermal_zone*/temp, and can be useful when monitoring the temperature of your Linux computer/server while running CPU intensive processes: simulation, gaming, etc...

You can download the .AppImage "binary" from here: https://github.com/gmagno/tmon/releases and run it immediately and conveniently, that is:

Install

wget https://github.com/gmagno/tmon/releases/download/v0.3.7/tmon-a461481-x86_64.AppImage
chmod +x tmon*.AppImage
# optional: you may put it somewhere convenient in your file system and add a symlink in /usr/local/bin/tmon

or if you prefer:

pip install tmonpy

Usage

./tmon*.AppImage -h

Examples

./tmon*.AppImage echo "Quick programs return a single value of temperature"
Quick programs return a single value of temperature


===================
Temp Monitor Report:

   Temp (°C) for a period of 0:00:00
   >> 58.0 °C <<

   /tmp/[email protected]
===================

./tmon*.AppImage bash -c 'echo not so quick ones will show a chart; sleep 6'
not so quick ones will show a chart


===================
Temp Monitor Report:

   Temp (°C) for a period of 0:00:06
   60.00  ┤
   59.86  ┤
   59.71  ┤
   59.57  ┤
   59.43  ┤
   59.29  ┤
   59.14  ┤
   59.00  ┼╮   ╭─
   58.86  ┤│   │
   58.71  ┤│   │
   58.57  ┤│   │
   58.43  ┤│   │
   58.29  ┤│   │
   58.14  ┤│   │
   58.00  ┤╰───╯

   >> min: 58.0 °C <<
   >> avg: 58.4 °C <<
   >> max: 59.0 °C <<

   /tmp/[email protected]
===================

you may also just run tmon without any arguments and it will run as you'd expect. Press Ctrl-C to terminate the process and get a temperature report

./tmon*.AppImage  # and wait a few seconds before pressing Ctrl-C
^C

===================
Temp Monitor Report:

   Temp (°C) for a period of 0:00:08
   60.00  ┤
   59.71  ┤
   59.43  ┤
   59.14  ┤
   58.86  ┤  ╭╮
   58.57  ┤  ││
   58.29  ┤  ││
   58.00  ┼╮╭╯│
   57.71  ┤││ │
   57.43  ┤││ │
   57.14  ┤││ │
   56.86  ┤╰╯ │
   56.57  ┤   │
   56.29  ┤   │
   56.00  ┤   ╰────

   >> min: 56.0 °C <<
   >> avg: 56.9 °C <<
   >> max: 59.0 °C <<

   /tmp/[email protected]
===================

Answer 15

One can also use bpytop. Install with:

sudo snap install bpytop

A more powerful version than htop, with CPU temperature and much more.

Answer 16

For Intel CPUs only You can use i7z.

i7z - A better i7 (and now i3, i5) reporting tool for Linux.

Install it :

sudo apt install i7z 

Then run it (it has to be run with sudo):

sudo i7z

Example output (see Temp column - scroll right...):

Real Current Frequency 4883.47 MHz [99.98 x 48.85] (Max of below)
    Core [core-id]  :Actual Freq (Mult.)      C0%   Halt(C1)%  C3 %   C6 %  Temp      VCore
    Core 1 [0]:       4883.47 (48.85x)      10.4    73.7    1.45    12.8    47      1.3547
    Core 2 [1]:       4871.56 (48.73x)      8.65    76.8     1.5    11.7    45      1.3547
    Core 3 [2]:       4877.61 (48.79x)      12.2    75.1       1    9.72    52      1.3547
    Core 4 [3]:       4880.70 (48.82x)      7.57    79.7       1    10.5    47      1.3547

Answer 17

computertemp is a simple applet that shows your current CPU temperature + it has some additional features like alarms. Unfortunately it's not possible (or at least I don't know how) to change its background color, so it doesn't look very nice with the standard Ubuntu theme.

It can be installed the same way as the sensors-applet described in evgeny's answer.

computertemp is not available in the newer Ubuntu repositories.

Answer 18

If you are using Ubuntu with MATE Desktop Environment, you can use MATE Sensors Applet:

1. Install the package:

   sudo apt-get install mate-sensors-applet
   

   And if you have Nvidia graphics card you can also install mate-sensors-applet-nvidia package.

2. Make right click on MATE Panel and click Add to Panel then choose Hardware Sensors Monitor

   

3. After adding you can setup it by doing right click on any sensor and selecting Preferences

   

   Here you can customize the list of sensors: CPU, Motherboard and GPU temperature, main voltages (Vcore, 3.3V, 5V, 12V, etc) and fan speeds. The full list depends on hardware (image above is for desktop with Nvidia graphics card).

4. The result will look like

   

Of course you can move this applet to the best location.

Answer 19

There are a lot of different places you might find the temperature listed in millidegrees. I finally found mine here:

/sys/devices/platform/coretemp.0/temp*_input

Here are some other places users have reported to have found their temperature

/proc/acpi/thermal_zone/THRM/temperature
/sys/class/thermal/thermal_zone*/temp
/sys/class/thermal/cooling_device*/temp
/sys/devices/platform/f71882fg.1152/temp*_input
/sys/devices/platform/coretemp.0/hwmon/hwmon*/temp*_input

Some of these are just symbolic links to the others. You may have to look carefully to find it

Answer 20

GUI alternatives for sensors command are Psensor and XSensors:

sudo apt install xsensors
sudo apt install psensor

For better detection of your hardware's sensors, you can also run following:

sudo apt install lm-sensors
sudo sensors-detect
sensors
watch -d -n 1 sensors

Answer 21

printf '%d°\n' $(sensors | grep 'id 0:' | awk '{ print $4 }') 2>/dev/null
55°

printf '%d\n' Will convert the value to integer in case you need it as a round number

---

Sources: Linuxhacks.org
Disclosure: I am the owner of Linuxhacks.org