So, I recently bought a Dell Perc H310 RAID controller to put in a Fujitsu Esprimo P700 E85+ Computer running Ubuntu Server 18.04.1 LTS. The Motherboard seems to have no UEFI, just a BIOS. From a hardware perspective I:
- connected a 500GB Boot drive straight onto the MoBo
- connected 2*3TB SATA drives through a SATA to mini-SAS cable splitter to the RAID controller
- configured a Raid0, RAID1 Virtual Drive in the Boot-Configuration-BIOS
and everything seems fine in the Controller's menu.
But when I boot Ubuntu (it's installed on the Boot HDD) the 6TB, 3TB RAID drive (RAID0 and 1 respectively) is nowhere to be found, nor any of the 2*3TB separate drives it consists of.
parted --list and
lsblk to check for the drive(s) and
lspci to check the controller.
The ouput of
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT loop0 7:0 0 87.9M 1 loop /snap/core/5328 loop1 7:1 0 86.6M 1 loop /snap/core/4486 sda 8:0 0 465.8G 0 disk ├─sda1 8:1 0 1M 0 part └─sda2 8:2 0 465.8G 0 part /
The output of
parted --list is:
Model: ATA WDC WD5000AAKX-0 (scsi) Disk /dev/sda: 500GB Sector size (logical/physical): 512B/512B Partition Table: gpt Disk Flags: Number Start End Size File system Name Flags 1 1049kB 2097kB 1049kB bios_grub 2 2097kB 500GB 500GB ext4
The output of
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:16.2 IDE interface: Intel Corporation 6 Series/C200 Series Chipset Family IDE-r Controller (rev 04) 00:16.3 Serial controller: Intel Corporation 6 Series/C200 Series Chipset Family KT Controller (rev 04) 00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a4) 00:1f.0 ISA bridge: Intel Corporation Q65 Express Chipset Family LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04) 01:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 2008 [Falcon] (rev 03)
And the output of
lspci -vv for the RAID controller is:
01:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 2008 [Falcon] (rev 03) Subsystem: Dell MegaRAID SAS 2008 [Falcon] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at e000 [size=256] Region 1: Memory at fe460000 (64-bit, non-prefetchable) [size=16K] Region 3: Memory at fe400000 (64-bit, non-prefetchable) [size=256K] Expansion ROM at fe440000 [disabled] [size=128K] Capabilities: <access denied> Kernel modules: megaraid_sas
Note: I also tried the RAID Ctrlr on a Windows machine, with a UEFI. It did not POST with the card, until I taped over PCIe lanes B5 and B6 (I found this advice somewhere online). After that, it did recognize a RAID0 configuration. Moving the card and disks back to the Ubuntu System and booting it there brought no success either. The controller behaves exactly as before, which is why I haven't removed the tape over the two lanes yet.
How should I proceed?