0

I have a strange experience...

When I switch on my laptop (HP Mini) with out pulling any strings... it boots but just before showing login greeter it gives me some "Low graphic" error... then I have to chose some options to fix this problem and pass... after login I see the WiFi device is not ready!...

BUT IF at GRUB time... I chose "Recovery Mode" and in the action selection of the recovery mode, I chose to just "BOOT NORMALLY"... It boots without any single graphic error or problem connecting WiFi...

I want to get rid of this "going to grub and select RECOVERY mode, each time I want to turn on my Laptop!"

PLEASE HELP! Thanks in advance!

P.S. following I provide some info about my hardware....

running $ sudo lshw -class display gaves me:

  *-display:0 UNCLAIMED
       description: VGA compatible controller
       product: Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller
       vendor: Intel Corporation
       physical id: 2
       bus info: pci@0000:00:02.0
       version: 00
       width: 32 bits
       clock: 33MHz
       capabilities: msi pm vga_controller bus_master cap_list
       configuration: latency=0
       resources: memory:58180000-581fffff ioport:60c0(size=8) memory:40000000-4fffffff memory:58000000-580fffff memory:c0000-dffff
  *-display:1 UNCLAIMED
       description: Display controller
       product: Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller
       vendor: Intel Corporation
       physical id: 2.1
       bus info: pci@0000:00:02.1
       version: 00
       width: 32 bits
       clock: 33MHz
       capabilities: pm bus_master cap_list
       configuration: latency=0
       resources: memory:58100000-5817ffff

and $ sudo lshw -class network gaves me:

  *-network
       description: Ethernet interface
       product: RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 0
       bus info: pci@0000:01:00.0
       logical name: eno1
       version: 02
       serial: c8:0a:a9:24:00:82
       size: 10Mbit/s
       capacity: 100Mbit/s
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s
       resources: irq:24 ioport:5000(size=256) memory:50010000-50010fff memory:50000000-5000ffff memory:57000000-5700ffff
  *-network
       description: Wireless interface
       product: BCM43225 802.11b/g/n
       vendor: Broadcom Corporation
       physical id: 0
       bus info: pci@0000:02:00.0
       logical name: wlp2s0
       version: 01
       serial: c4:17:fe:86:de:0f
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless
       configuration: broadcast=yes driver=wl0 driverversion=6.30.223.271 (r587334) ip=192.168.1.47 latency=0 multicast=yes wireless=IEEE 802.11
       resources: irq:17 memory:56000000-56003fff

and the result of the script mentioned in another AskUbuntu post could be found here

|improve this question
  • Recovery mode uses nomodeset as boot parameter by default. Does nomodeset work with normal boot? And since only Intel do any of these work instead of nomodeset. Some other Intel boot options Each line is one that may work acpi_osi=Linux or acpi_backlight=vendor or i915.i915_enable_rc6=1 You also can try just setting a specific screen resolution. askubuntu.com/questions/496944/… – oldfred Jun 21 '18 at 3:56

Your Answer

By clicking "Post Your Answer", you acknowledge that you have read our updated terms of service, privacy policy and cookie policy, and that your continued use of the website is subject to these policies.

Browse other questions tagged or ask your own question.