7

I have Ubuntu 18.04 LTS installed.

I installed Arduino IDE v1.8.5 as a snap with

snap install arduino-mhall119

I have added my user to dial-out group and rebooted:

sudo usermod -a -G dialout $USER

$ groups 
username adm dialout cdrom sudo dip plugdev lpadmin sambashare

I connected my Arduino Nano to the laptop, it is detected on port /dev/ttyUSB0 (ch341-uart).

$ ls /dev/ttyUSB0 -al
crw-rw---- 1 root dialout 188, 0 авг 13 11:59 /dev/ttyUSB0

I tried to upload the simpliest Blink sketch and get the following errors in the terminal:

$ arduino-mhall119.arduino 


avrdude: ser_open(): can't open device "/dev/ttyUSB0": Permission denied  
Problem uploading to board.  See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.**

Also I have installed arduino 1.8.5 with umake - it can access serial port in usual way.

Note: we already have similar question here, but the solution was to use package from umake, not fix for the Snap.

So my question is: How to make Arduino (Snap) access serial port /dev/ttyUSB0 (or /dev/ttyACM0)?

Update: connecting serial-port to the snap fails with the following message

$ snap connect arduino-mhall119:serial-port 
error: snap "core" has no "serial-port" interface slots

Current interfaces are:

$ snap interfaces | grep arduino
:home                            arduino-mhall119,gedit,organize-my-files,vlc
:network                         arduino-mhall119,gedit,organize-my-files,pulsemixer,vlc
:unity7                          arduino-mhall119,gedit,organize-my-files,vlc
:x11                             arduino-mhall119,organize-my-files,pulsemixer,vlc
-                                arduino-mhall119:serial-port

Changing permissions of serial port to 777 with sudo chmod 777 /dev/ttyUSB0 does not help.

The following do not work too (because of syntax errors):

$ sudo snap connect arduino-mhall119:arduino
error: snap "arduino-mhall119" has no plug named "arduino"

$ snap connect arduino-mhall119:/dev/ttyUSB0
error: snap "arduino-mhall119" has no plug named "/dev/ttyUSB0"

$ snap connect arduino-mhall119
error: cannot resolve connection, plug snap name is empty

Information about YAML-manifest:

$ ls -l /snap/arduino-mhall119/current/meta/snap.yaml
-rw-r--r-- 1 root root 353 июл 28 00:20 /snap/arduino-mhall119/current/meta/snap.yaml

$ cat /snap/arduino-mhall119/current/meta/snap.yaml |grep -A 12 slots

$ cat /snap/arduino-mhall119/current/meta/snap.yaml |grep -A 5 plug
    plugs:
    - x11
    - unity7
    - home
    - network
    - serial-port
10

Install the snap in classic mode to allow access to ports

$ snap install arduino-mhall119 --classic

It's that simple. You should now have access to your serial ports! Happy Hacking!

Note: info below are needed for old Arduino 1.6.10.



Some interesting links that helped find the answer

Auto connected serial port interface

Lundamar says: Until the serial-port gadget/interface is improved to give access to all system serial devices you can get your snap working by simply installing it non-confined like so:

$ snap install tio --classic

It’s better than nothing but it surely would be best to run it confined with allowed access to serial tty devices.

Interfaces - serial-port

Interfaces reference:

serial-port
Can access serial ports. This is restricted because it provides privileged access to configure serial port hardware. Note that the slot is meant to be implemented by a gadget snap (this is not provided by the core snap).

Gadget providing serial-port slot

  • Made your answer more comprehensive, so you can remove all comments below the question. Thank you for all you help! – N0rbert May 9 '18 at 16:37
  • Thank you. I was having the same problem and your solution worked for me. I don't understand though. A few months back my Arduino IDE was working fine, I didn't change anything, and now I just wasted 3 hours, added permissions to the ttyUSB0 (which were there to begin with), I already belonged to the group dialout, rebooted multiple times and prayed over and over. And a simple '--classic' solved it. Seriously man, wtf! I read your answer multiple times, it is gibberish to me. I'd think installing the IDE from Ubuntu Software manager should have worked right out of the box (like it did before). – ColdTuna Aug 30 '18 at 12:48
  • Well, now there isn't the esp32 in the Board Manager. It feels like it's 1996 all over again. – ColdTuna Aug 30 '18 at 13:00
  • Never mind, I'm kinda brain dead already and forgot to add the esp32 URL to the Board Manager in Preferences... thanks again for your solution. – ColdTuna Aug 30 '18 at 13:17

protected by N0rbert Sep 30 '18 at 15:00

Thank you for your interest in this question. Because it has attracted low-quality or spam answers that had to be removed, posting an answer now requires 10 reputation on this site (the association bonus does not count).

Would you like to answer one of these unanswered questions instead?

Not the answer you're looking for? Browse other questions tagged or ask your own question.