Take the 2-minute tour ×
Ask Ubuntu is a question and answer site for Ubuntu users and developers. It's 100% free, no registration required.

whenever I try to boot with linux kernel 3.0.0.13 (the one installed by the upgrades) I get a Kernel Panic error:

VFS: Cannot open root device "sda1" or unknown block (0,0) Please append a correct "root=" boot option;

Luckily enough if I boot using the previous version I don't have any issue. How can I solve this? Where should I append the correct root= option? If I don't get this Kernel to work, how can I remove it as the default and stick to the older one?

share|improve this question
    
Same problem here. The main difference I observe is that up to 3.0.0.12, the grub conf tries to identify the hard disk using its UUID, 3.0.0.13 now uses /dev/sda6 .. weird ... –  Dan Soap Nov 28 '11 at 16:19
add comment

2 Answers

up vote 5 down vote accepted

You haven't provided much information with logs and such to proceed with but I am guessing most probably this error you're facing is because the kernel is confused by a IDE/SATA drive. Doing a quick Google search led me to link 1, link 2, link 3

Following is the excerpt from a link referred to by one of the links above:

Most likely one of the most occurring issue (but once you solved it, you most likely are never going to see it again):

Unable to mount root fs on unknown-block(0,0)

or

VFS: Cannot open root device "sda3" or unknown-block(8,3)
Please append a correct "root=" boot option; here are the available partitions:
  sda driver: sd
    sda1 sda2

The digits 0,0 or 8,3 can be different in your case - it refers to the device that the kernel tries to access (and which fails). Generally speaking one can say that, if the first digit is 0, then the kernel is unable to identify the hardware. If it is another digit (like 8), it is unable to identify the file system (but is able to access the hardware).

The problem here is that the kernel that you are booting cannot translate the root=/dev/... parameter you gave it (inside the boot loader configuration) into a real, accessible file system. Several reasons can result in such a failure:

  • the kernel configuration is missing drivers for your HDD controller (cases 1, 4, 5)
  • the kernel configuration is missing drivers for the bus used by your HDD controller
  • the kernel configuration is missing drivers for the file system you are using
  • the device is misidentified in your root= parameter (cases 2, 3)

Resolving the issue is easy if you know what the reason is. You most likely don't, so here's a quick check-up.

Open the kernel configuration wizard (the make menuconfig part) so that you can update the kernel configuration accordingly.

  • Check if you have built in (and not as a module) support for the bus / protocol that your harddisk controller uses.
  • Most likely this is PCI support, SATA support (which is beneath SCSI device support), ...
  • Check if you have built in (and not as a module) support for the HDD controller you use. One of the most frequent cases: you selected support for your harddisk controller protocol (IDE, SATA, SCSI, ...) but forgot to
    select the HDD controller driver itself (like Intel PIIX). Try
    running the following lscpi command, and paste its output on
    http://kmuto.jp/debian/hcl/. The site will show you which kernel drivers you need to select for your system. Within the menuconfig,
    you can type "/" to open the search function, and type in the driver
    name to find out where it resides. # lspci -n
  • Check if you have built in (and not as a module) support for the file system(s) you use.
  • Say your root file system uses btrfs (which I definitely don't recommend) but you didn't select it, or selected it to be built as a
    module, then you'll get the error you see. Make sure the file system
    support is built in the kernel.
  • Check if the kernel parameter for root= is pointing to the correct partition.

    This isn't as stupid as it sounds. When you are booted with one kernel, it might list your disks as being /dev/sda whereas your (configured) kernel is expecting it to be /dev/hda. This is not because kernels are inconsistent with each other, but because of the drivers used: older drivers use the hda syntax, newer sda.

    Try switching hda with sda (and hdb with sdb, and ...).

    Also, recent kernels give an overview of the partitions they found on the device told. If it does, it might help you identify if you misselected a partition (in the example given at the beginning of this section, only two partitions are found whereas the kernel was instructed to boot the third). If it doesn't, it is most likely because the kernel doesn't know the device to begin with (so it can't attempt to display partitions).

  • Check if the kernel that is being boot by the boot loader is the correct kernel. I have seen people who, after building a first kernel (which doesn't boot), forget that they have to mount /boot before the overwrite the kernel with a new one. As a result, they copy the kernel to the root file system (/) whereas the boot loader still expects the kernel image to be on the /boot partition.

share|improve this answer
1  
Hi, it passed a lot of time, but thanks. I had a faulty CD-Rom, removing that everything worked fine! –  lucacerone Mar 13 '12 at 17:36
add comment

After reading this answer which explains what is going on, try using the [Boot-Reapir CD][1][1]: https://help.ubuntu.com/community/Boot-Repair

Worked great at repairing the "the device is misidentified in your root= parameter (cases 2, 3)".

share|improve this answer
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.