Take the 2-minute tour ×
Ask Ubuntu is a question and answer site for Ubuntu users and developers. It's 100% free, no registration required.

my hd was moved into new reassembled pc. Everything works, except networking (wired/wireless). Linux can see the devices, but cannot activate. Following are data that i can get:

# uname -a
Linux fxt-AcAsp-L3600 3.2.0-39-generic #62-Ubuntu SMP Wed Feb 27 22:05:17 UTC 2013 i686 i686 i386 GNU/Linux

# nm-tool
** (process:3207): WARNING **: Could not initialize NMClient /org/freedesktop/NetworkManager: The name org.freedesktop.NetworkManager was not provided by any .service files
NetworkManager Tool
State: unknown

# lshw -C network
*-network DISABLED
description: Ethernet interface
product: AR8151 v2.0 Gigabit Ethernet
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:02:00.0
logical name: eth1
version: c0
serial: 94:de:80:96:36:32
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress vpd bus_master cap_list 
ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI 
firmware=N/A 
latency=0 
link=no 
multicast=yes 
port=twisted pair
resources: irq:17 memory:fdec0000-fdefffff ioport:df00(size=128)

*-network UNCLAIMED
description: Network controller
product: Ralink corp.
vendor: Ralink corp.
physical id: 0
bus info: pci@0000:03:00.0
version: 00
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list
configuration: latency=32 maxlatency=4 mingnt=2
resources: memory:fddf0000-fddfffff

invoke-rc.d networking restart
* Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces
* Reconfiguring network interfaces...

# dhclient eth1
RTNETLINK answers: Operation not permitted

# cat /etc/resolv.conf
# Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8)
# DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN

# ping 192.168.1.1
connect: Network is unreachable

# ifconfig -a
eth1        Link encap:Ethernet  HWaddr 94:de:80:96:36:32  
            BROADCAST MULTICAST  MTU:1500  Metric:1
            RX packets:0 errors:0 dropped:0 overruns:0 frame:0
            TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
                      collisions:0 txqueuelen:1000 
            RX bytes:0 (0.0 B)  
            TX bytes:0 (0.0 B)
            Interrupt:17 
lo          Link encap:Local Loopback  
            inet addr:127.0.0.1  
            Mask:255.0.0.0
            inet6 addr: ::1/128 Scope:Host
            UP LOOPBACK RUNNING  MTU:16436  Metric:1
            RX packets:4388 errors:0 dropped:0 overruns:0 frame:0
            TX packets:4388 errors:0 dropped:0 overruns:0 carrier:0
                      collisions:0 txqueuelen:0 
            RX bytes:320020 (320.0 KB)  TX bytes:320020 (320.0 KB)

How should i activate the network card (it's onboard) and the wifi. Please give me a hint.

share|improve this question

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Browse other questions tagged or ask your own question.