Take the 2-minute tour ×
Ask Ubuntu is a question and answer site for Ubuntu users and developers. It's 100% free, no registration required.

I'm using GParted to shrink the partition on my 500 GB external hard drive to a 220 GB partition. It contains about 210 GB of data. I'm shrinking it to convert FAT32 to EXT2. It has been almost an hour. My hard disk heats up so I have continuous ventilation to keep it cool. Is this lengthy time taken by GParted normal? If not, then how do I safely disconnect it? I don't mind losing the data, but the hard disk is really important. Any suggestions? Also, will running the hard disk for such long hours harmful?

share|improve this question

2 Answers 2

up vote 9 down vote accepted

It's quite normal for dynamic resizing operations--and particularly shrinking--to take a long time. Files are spread across much, and perhaps most, of the original partition. They have to be re-pieced together to fit them in a smaller space, and the information about where their pieces exist has to be updated. If you are also having the partition automatically converted from FAT32 to ext2, that may take a while as well, as the files are stored somewhat differently.

If it takes more than a day, then I would start thinking there was something wrong.

As for whether or not it's OK to run your hard drive at near its maximum capacity for reads and writes, for hours at a time: yes, this is fine. Your hard drive is, among other things, a mechanical device, so the more it's used, the higher the likelihood of mechanical failure. But all hard drives fail eventually, and there's no reason to expect this one will fail any sooner, just because it runs heavily for hours.

Of course, if it's getting too hot, that is a problem. A properly constructed computer should never allow this to happen, even if the hard drive is reading and writing at 100% capacity for days, weeks, or months without interruption. (Depending on what hard drive you've purchased, running it like this for months might or might not bring about very early failure.) But if you find it is hot, and you're able to cool it with externally applied ventilation, that should be fine.

I don't mind losing the data,but the hard disk is really important.

If you have to cancel the operation, click Cancel. Really anything except cutting power to your computer or to the drive, won't physically damage the drive. Shutting down the operating system, using any method of harshness less than or equal to REISUB, will not be a problem. Even cutting power to the machine is unlikely to cause any real damage, although I would definitely avoid it when possible.

However, you may want to rethink the value you put in a single drive. All hard drives fail eventually, you can't prevent them from failing, and you can't prevent some of them (essentially selected at random) from failing long before you would expect them to fail. Some drives last longer than others (for some uses), and some drives are less likely to fail "early," but hard drives are replaceable (even in laptops) for a reason.

To put it another way: Hard drives' lifetimes are limited, so much so that in any computer where some other component fails first, the computer's craftsmanship should be questioned.

share|improve this answer
    
Thank you for that well written comprehensive answer. Oh btw,its an external Hard drive. –  Schweinsteiger Aug 19 '12 at 21:25
    
@Schweinsteiger You might expect an external drive (depending on the interface) to be somewhat slower than an internal drive, because each access may take a little longer. As for the drive's lifetime, an external drive is actually an internal drive in an enclosure, so the characteristics and design specifications of the internal drive would be what you'd want to consult, if you wanted to determine how suited the drive is to your needs. (Of course, dynamic partitinon resizing operations probably aren't your usual pattern of use.) –  Eliah Kagan Aug 19 '12 at 21:29
    
Oh alright. Thanks again :) –  Schweinsteiger Aug 19 '12 at 21:34

Most external drives AFAIK do not have cooling fans, so under the process you described, overheating is expected...and unwanted. There is no need to wear out your hardware before the end of its design lifetime.

I found it quicker and more kind to the hardware, if you copy (not "move") the files to another hard drive temporarily. Or perhaps compress the existing files (7z, tar, rar, or zip) to one big file, then copy to another drive.

If it's OK to destroy the original files, use GParted (or other disk/partition manager) to immediately reformat the whole drive, defining whatever partitions you want (however many, however big, and whatever filesystems you prefer).

share|improve this answer

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.