13

I have a year-old drive that's giving me trouble. Copying data to it fails after about 8-10GB of transfers. It spontaneously changes to 'read only'. It's properly formatted ext4, I'm the owner. Searching online, it looks like this is a symptom of a failing drive.

How do I confirm this, since the SMART tests indicate otherwise?

I did the obvious like check the Disk Utility, and ran the extended SMART test. All results from Disk Utility come back perfect. Read error rate and reallocated sectors are showing zero.

I'm guessing this disk is bad and SMART isn't detecting it, though I don't understand why. I'd like to confirm what the problem is.

I'm having no problems with the other disks in the machine.

fstab:

proc /proc proc nodev,noexec,nosuid 0 0 UUID=62e11126-3f06-43f0-bd5a-29b411bb8160 / ext4
errors=remount-ro 0 1
UUID=5e2d6348-be6e-4d5d-8f7f-1a5c1cab7db2 /home ext4
defaults 0 2 UUID=97e594a3-c783-4c73-97c0-682afcdc88b6 none swap sw 0 0
/dev/disk/by-label/Media /media/Media ntfs-3g defaults,user,locale=en_GB.utf8 0 0

Output of dmesg | less: (There are hundreds more 'Buffer I/O error' lines above)

[22734.511487] Buffer I/O error on device sda1, logical block 302203
[22734.511489] Buffer I/O error on device sda1, logical block 302204
[22734.511490] Buffer I/O error on device sda1, logical block 302205
[22734.511492] Buffer I/O error on device sda1, logical block 302206
[22734.511494] Buffer I/O error on device sda1, logical block 302207
[22734.511496] EXT4-fs warning (device sda1): ext4_end_bio:251: I/O error writing to inode 9437465 (offset 4194304 size 524288 starting block 302215)
[22734.511500] ata1: EH complete
[22734.511616] EXT4-fs error (device sda1): ext4_journal_start_sb:327: Detected aborted journal
[22734.511619] EXT4-fs (sda1): Remounting filesystem read-only
[22734.519343] EXT4-fs error (device sda1) in ext4_da_writepages:2298: IO failure
[22734.538566] EXT4-fs (sda1): ext4_da_writepages: jbd2_start: 601 pages, ino 9437474; err -30
[22734.560225] ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x400100 action 0x6 frozen
[22734.560253] ata1.00: irq_stat 0x08000000, interface fatal error
[22734.560256] ata1: SError: { UnrecovData Handshk }
[22734.560258] ata1.00: failed command: WRITE FPDMA QUEUED
[22734.560262] ata1.00: cmd 61/00:00:3f:68:25/04:00:00:00:00/40 tag 0 ncq 524288 out
[22734.560263]          res 40/00:04:3f:68:25/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[22734.560264] ata1.00: status: { DRDY }
[22734.560268] ata1: hard resetting link
[22735.047845] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[22735.052069] ata1.00: configured for UDMA/33
[22735.067810] ata1: EH complete
[22735.136249] ata1.00: exception Emask 0x10 SAct 0x3f SErr 0x400100 action 0x6 frozen  

fsck result:

tom@1204-Desktop:~$ sudo fsck /dev/sda1
[sudo] password for tom: 
fsck from util-linux 2.20.1
e2fsck 1.42 (29-Nov-2011)
New_Volume: recovering journal
New_Volume contains a file system with errors, check forced.
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
Free blocks count wrong (236669077, counted=236701938).
Fix<y>? yes

Free inodes count wrong (61048336, counted=61048349).
Fix<y>? yes

Last but not least is the read/write screengrab, this is new. It used to stay pretty consistent over the duration of the test.

read write screengrab

EDIT- When I powered on this morning the drive had changed from /dev/sda to /dev/sdc, strange. I'm certain that hasn't happened before and I'm certain it was /dev/sda. I swapped SATA cables with a known good one and saw that same failure at about 10GB transfers. I didn't change SATA ports yet, I'll try that next. (Edit #2, it was the SATA port, changing it fixed the problem. Flagging this as too localized.)

Output of sudo smartctl -a /dev/sda

=== START OF INFORMATION SECTION === Model Family:     Western Digital Caviar Black Device Model:     WDC WD1002FAEX-00Y9A0 Serial Number:    WD-WCAW30776630 LU WWN Device Id: 5 0014ee 25acf2868 Firmware Version:
05.01D05 User Capacity:    1,000,204,886,016 bytes [1.00 TB] Sector Size:      512 bytes logical/physical Device is:        In smartctl database [for details use: -P show] ATA Version is:   8 ATA Standard is:  Exact ATA specification draft version not indicated Local Time is:    Fri May 25 07:16:18 2012 BST SMART support is: Available - device has SMART capability. SMART support is: Enabled

=== START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED

General SMART Values: Offline data collection status:  (0x82)   Offline data collection activity
                    was completed without error.
                    Auto Offline Data Collection: Enabled. Self-test execution status:      (   0)  The previous self-test routine completed
                    without error or no self-test has ever 
                    been run. Total time to complete Offline  data collection:      (16500) seconds. Offline data collection capabilities:           (0x7b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    Conveyance Self-test supported.
                    Selective Self-test supported. SMART capabilities:            (0x0003)  Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer. Error logging capability:        (0x01) Error logging supported.
                    General Purpose Logging supported. Short self-test routine  recommended polling time:    (   2) minutes. Extended self-test routine recommended polling time:    ( 170) minutes. Conveyance self-test routine recommended polling time:      (   5) minutes. SCT capabilities:
           (0x3035) SCT Status supported.
                    SCT Feature Control supported.
                    SCT Data Table supported.

SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE   1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always  
-       0   3 Spin_Up_Time            0x0027   176   173   021    Pre-fail  Always       -       4183   4 Start_Stop_Count        0x0032 100   100   000    Old_age   Always       -       774   5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always  
-       0   7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0   9 Power_On_Hours          0x0032   093   093   000    Old_age   Always       -       5518  10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always  
-       0  11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -       0  12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       772 192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always  
-       39 193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       736 194 Temperature_Celsius     0x0022  118   111   000    Old_age   Always       -       29 196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always  
-       0 197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0 198 Offline_Uncorrectable   0x0030   200   200   000    Old_age   Offline      -       0 199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always  
-       0 200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

SMART Error Log Version: 1 No Errors Logged

SMART Self-test log structure revision number 1 Num  Test_Description  Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%      5514         -

SMART Selective self-test log data structure revision number 1  SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing Selective self-test flags (0x0):   After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
3
  • please include the output of sudo smartctl -a /dev/sda
    – ish
    May 24, 2012 at 23:47
  • 6
    Try replacing the SATA cable; it may be bad.
    – psusi
    May 24, 2012 at 23:48
  • @psusi Good idea, unfortunately that didn't help. May 25, 2012 at 8:12

1 Answer 1

13

How do I confirm this, since the SMART tests indicate otherwise?

The SMART tests are "isolated", i.e once smartctl commands the drive to do a test, the drive handles everything internally and then reports back. So this may not reveal problems between the drive/controller and your motherboard.

  • The obvious inference is a bad cable, but that isn't supported by the disk-utility graphs; reads should be affected too. Still, swap cables/SATA ports and see if it makes a difference.

  • Run the long self-test with smartctl -t long ; fastest in captive mode -C (unmount all partitions!), and when done, check status/errors with -l (the test will abort as soon as an error is detected)

  • If that works out, do you remember anything that could have triggered this problem software-side? Kernel upgrade/downgrade, etc.?

  • Finally, if all your other disks are fine, this may very well be a bizarre bug with the drive's write-cache controller. Backup data and RMA it as soon as possible.

    (post any questions in comments and I'll update the answer. Good luck!)

6
  • I swapped the SATA port and copied >200GB no problem, looks like that fixed it. Thanks for the detailed answer. May 25, 2012 at 12:03
  • 5
    @TomBrossman, this doesn't happen to be a sandybridge chipset system from around February of 2011 does it? They had a defect that caused the sata ports to break down over time and had a big recall.
    – psusi
    May 25, 2012 at 15:29
  • @psusi It is, and I've sent an email to ASUS support asking them what they want to do to correct it. I didn't even know about the recall. Good to know! May 25, 2012 at 18:16
  • 3
    @TomBrossman, I finally got around to making them replace mine 6 months ago. They did give me some grief that the recall had ended, but they finally did send me a replacement. Check and see if the bios lists the stepping of the southbridge and if it is B2, that's the recalled one and they should replace it.
    – psusi
    May 25, 2012 at 18:46
  • 3
    @TomBrossman: it's a defective Intel SATA controller on the mobo. See this to verify: event.asus.com/2011/mb/identify_b3_motherboards Very good catch @psusi! If you are on defective B2, one solution is to use SATA3 ports which are a third party controller, usually Marvell. Also contact Asus-intel paid mfrs and retailers for this snafu, no skin off their back, they MUST replace it if it's B2.
    – ish
    May 25, 2012 at 20:28

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .