Ask Ubuntu is a question and answer site for Ubuntu users and developers. Join them; it only takes a minute:

Sign up
Here's how it works:
  1. Anybody can ask a question
  2. Anybody can answer
  3. The best answers are voted up and rise to the top

When I copy files to the USB device, it takes much longer than in windows (same usb device, same port) it's faster than USB 1.0 speeds (1MB/s) but much slower than USB 2.0 speeds (12MB/s). To copy 1.8GB takes me over 10 minutes (it should be < 3 min.) I have two identical SanDisk Cruzer 8GB sticks, and I have the same problem with both. I have a super talent 32GB USB SSD in the neighboring port and it works at expected speeds.

The problem I seem to see in the GUI is that the progress bar goes to 90% almost instantly, completes to 100% a little slower and then hangs there for 10 minutes. Interrupting the copy at this point seems to result in corruption at the tail end of the file. If I wait for it to complete the copy is successful.

Any ideas? dmesg output below:

[64059.432309] usb 2-1.2: new high-speed USB device number 5 using ehci_hcd
[64059.526419] scsi8 : usb-storage 2-1.2:1.0
[64060.529071] scsi 8:0:0:0: Direct-Access     SanDisk  Cruzer           1.14 PQ: 0 ANSI: 2
[64060.530834] sd 8:0:0:0: Attached scsi generic sg4 type 0
[64060.531925] sd 8:0:0:0: [sdd] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB)
[64060.533419] sd 8:0:0:0: [sdd] Write Protect is off
[64060.533428] sd 8:0:0:0: [sdd] Mode Sense: 03 00 00 00
[64060.534319] sd 8:0:0:0: [sdd] No Caching mode page present
[64060.534327] sd 8:0:0:0: [sdd] Assuming drive cache: write through
[64060.537988] sd 8:0:0:0: [sdd] No Caching mode page present
[64060.537995] sd 8:0:0:0: [sdd] Assuming drive cache: write through
[64060.541290]  sdd: sdd1
[64060.544617] sd 8:0:0:0: [sdd] No Caching mode page present
[64060.544619] sd 8:0:0:0: [sdd] Assuming drive cache: write through
[64060.544621] sd 8:0:0:0: [sdd] Attached SCSI removable disk
share|improve this question
Linux defers disk writes in exchange for performing other tasks faster. Just a guess, try running sync and see if it doesn't speed up the process. <--untested but possible – RobotHumans Apr 14 '12 at 22:43
that doesn't make sense that it would defer it for one type of USB but not another. Also I seem to recall linux calls sync every 30 seconds or so? Might be outdated. I'm expecting this is some kind of driver or compatibility issue since it depends on the type of device. – Eloff Apr 15 '12 at 0:37
The being faster on other USB thumbdrives isn't in your question. If it were, I would have suggested looking in to hdparm. So it makes sense if you view it from the perspective of someone who doesn't know your whole set-up, but depends on your question for details – RobotHumans Apr 15 '12 at 0:39
"I have a super talent 32GB USB SSD in the neighboring port and it works at expected speeds." it was in there, but well hidden I will admit :) So what's this hdparm stuff you allude to? – Eloff Apr 15 '12 at 20:34
Okay, SSD and flash memory are SO not the same thing. But moving along, hdparm is a utility that lets you set access/spin speeds for drive manually – RobotHumans Apr 15 '12 at 20:44

Why is copying to my USB drive so slow in Linux (and faster in Windows)?

Reason 1. File caching can make writes appear slower or faster

The problem I seem to see in the GUI is that the progress bar goes to 90% almost instantly, completes to 100% a little slower and then hangs there for 10 minutes.

One thing you need to understand is file caching. Linux (and Windows) will use otherwise "empty" RAM to cache read/write operations and make them faster on subsequent accesses. Caching copy operations to slow devices results in the behavior you see -- the "fast completion" is actually writing to the cache, and then it slows and stops because the actual flushing of the data in the cache (sync) to the slow device is taking very long. If you abort at that point, the data is corrupted (as you noted) since the sync never finished.

Such copying in Windows may seem faster (including the reported MB/sec speeds) because sometimes Windows will not wait for the sync, and declare the job completed as soon as the data is written to cache.

Reason 2. Writing lots of files, especially small ones, is slow

To copy 1.8GB

Because of the way flash memory and filesystems work, the fastest throughput (speed) is achieved when writing very large files. Writing lots of small files, or even mixed data containing a number of small files can slow the process down a lot. This affects hard drives too, but to a somewhat lesser extent.

Reason 3. Write speeds of a USB stick and an SSD cannot be compared

I have a super talent 32GB USB SSD in the neighboring port and it works at expected speeds.

  • A garden variety USB stick usually consists of flash memory chips that are written to serially (sequentially), and does not have any cache of its own.

  • An SSD, on the other hand, contains a controller which writes to the flash memory chips parallel, increasing the throughput by a factor of 2 or more over the USB stick.

    • If your 32GB SSD had 4x 8GB chips, it would still be 4x faster than the USB stick at any write operation.
    • The SSD also contains RAM cache (like hard disks), so it can quickly store incoming data in the cache and tell the OS that it's done, while it still has to actually write that data to the flash memory.
  • So, with one large file, your 32GB GB with the 4x structure we assumed, would be 4x as fast; with many small files, it would be 10x or more faster because it could intelligently store them in its cache.

To sum up, these are the reasons why file copying to USB sticks may appear slower in Linux. Is it actually slower because of a hardware/driver issue or whatever....

Doing a proper comparison of write speeds between Linux and Windows

  • First of all, forget about the SSD because of reason 3. It's like oranges and apples.
  • To negate the effects of reason 1 (caching) and reason 2 (small files), you need to test with a single large file, larger than the amount of RAM on the test system.
  • In Linux you can create it with dd if=/dev/urandom of=largetest bs=1M count=7500, which gives you a 7500 MB test file. Assuming your system has less than 4GB or so of RAM, it's good enough. Copy that to a freshly formatted Sandisk 8GB stick, and time it.
  • Reboot in Windows, and copy largetest from the USB stick to your hard disk. Reboot again (to remove it from the cache). Then format the USB stick (same vfat/FAT32!), and copy largetest from the hard disk to the stick.
  • How do the times compare?
share|improve this answer
cc: @Eloff Re Reason 1: Yes, cache syncing can certainly affect apparent write times. But would cache alone explain why it hangs there for 10 minutes?? I think we need more details from OP. Re Reason 2: Why do you assume this transfer consisted of many small files? I do not think the OP provides any details about this 1.8GB transfer, does he? Re Reason 3: Yes, SSD is a different beast. It also would probably be attached via SATA and not USB. I think the OP simply mis-spoke and referred to a USB stick as an SSD. But again, no way of knowing unless we get more details from the OP. – irrational John May 31 '12 at 16:11
This answer blatantly ignores how the question was formulated. The question clearly talks about one big file, and the fact that interrupting the copy results in a mangled file. – zrajm Feb 28 '14 at 17:48
@zrajm that's true. However for people like me bumping in the same problem, this is very helpful. – Pithikos Oct 20 '14 at 16:00

Just umount the device if it is automounted already, and manually mount it to /mnt/foldername.

In my case,

umount /media/usb0
mount /dev/sdb1 /mnt/sam

After that it is coping very fast.

share|improve this answer
This, along with rsync instead of cp seems to do the trick. – Power-Inside Jan 26 at 10:52
This didn't make any difference to my situation. Also, this isn't really a solution without some theory as to why this is supposed to make a difference. – LondonRob May 17 at 10:29

Found the fix all i did was unmount, remove drive, and run sudo modprobe ehci_hcd in the Terminal. Insert drive and agian sudo modprobe ehci_hcd when I put the drive in and wow 20/mbs thought i would share. Hope I dont have to do it every time... but it's not to hard... says they fixed the bug.

share|improve this answer
Seriously?? That bug report is from December of 2007 and references Ubuntu gutsy 7.10. (FYI: @MarcoCeppi) – irrational John May 31 '12 at 16:03
@irrationalJohn I didn't provide the answer, I just cleaned it up. Secondly just because a bug report is old, doesn't mean it's not still valid. It's being triaged according this – Marco Ceppi May 31 '12 at 16:36
@MarcoCeppi Yes, I know you only edited. That's why I prefaced with "FYI:". I figured if you edited it you might (or might not) be interested. I figured if you didn't care, you'd just ignore the notice. As for an old bug report still having relevance ... Over 4 years ago and I think at least 8 (?) releases later? For a performance bug? Sure, it may be possible, but it's not the first place I'd look. FWIW. – irrational John May 31 '12 at 16:54

I think the chances are very low that it is a port issue. It is more likely a LINUX (or linux configuration) issue - googgle around and you will find thousands of issue reports about slow USB in linux/ubuntu. For me it is almost a showstopper for linux - I now have an Ubuntu 12.04 LTS and still have this issue (so I rather use the Win7 setup - mainly/only because of this). This issue (or something with similar symptoms) is there for several years now, apparently no fix. And during this time I tried several physical PCs with several different ubuntu versions (default config) and 2-3 different USB sticks....

share|improve this answer

When you look in /etc/mtab, do you see that the device has been mounted with the "flush" option?

If so, this could be the cause of the problem (it was for me). Just unmount the device and remount it, it shouldn't be set by default.

share|improve this answer
The flush option is set by default, any way to stop this? – Ben Lutgens Mar 24 '14 at 17:52
@ Ben Lutgens - Yes, you can put your own entry in /etc/fstab that doesn't have the flush options. Use sudo blkid to find the relevant device UUID and put an entry such as UUID="your device uuid here" /mnt/<your mount point here> uid=1000,gid=1000,fmask=0022,dmask=0022 0 0. Change the uid, gid to match the userid and groupid of the normal user that you use (as found by getent passwd <your user>). – A.Danischewski Oct 28 '15 at 17:07

Silly question, but trying to narrow it down. Have you had similar performance from other USB flash drives (not the SSD) in BOTH ports? My wife damaged a USB port on her computer and that caused many failures and re-writes. It did eventually work, but verrrrry slow. Changing USB ports made the difference for her (that and a USB extension so she had another "front" port).

share|improve this answer

If you switch to a USB 3.0 , you will go from 1mb/s to a woping 5-8mb/s. I switch to a 3.0 USB pci and external HD and haven't looked back.

share|improve this answer

I had some problems also with transfer rate on a WD external disk, after opening it in a windows SO, i always used LINUX, after that the transfer rate was like 1.5mb/s than i unmount the external hard drive runed dmesg there it was saying that sdb1 it was unporperly unmounted, runed a fsck, that made a few repairs and after that 20mb/s of transfer rate again when copiyng from sda to external disk. fsck is always a risk if you have data, but it worked for me, with no data loss.

share|improve this answer

Your Answer


By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.