28

It's NTFS. It's USB2. I'm using Ubuntu 13.04. It works perfectly fine on Windows (which excludes cable and hardware problems). I have two Ubuntu computers and it's not detected on either. It's about 500 GB.

Summary: video explaining the solution

Edits:

Following the first link, I input sudo lsusb in a terminal; before and after connecting the HDD. The difference was Bus 001 Device 012: ID 14cd:6116 Super Top M6116 SATA Bridge. There it is! ("sata bridge" used to appear in a windows notification when I plugged in the HDD in!). ...This means that Ubuntu detects it but is it not mounting it?


I tried this:

sudo mount /dev/sdb1 /mnt

But gives this:

mount: special device /dev/sdb1 does not exist

I also tried:

sudo mount /dev/sdc1 /mnt

but it stays with no output forever. I left it in background for about 30 min.s.


sudo fdisk -l gives out this:

Disk /dev/sda: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xa42d04a3
 Device Boot      Start         End      Blocks   Id  System
/dev/sda1              63       80324       40131   de  Dell Utility
/dev/sda2   *       80325   102481919    51200797+   7  HPFS/NTFS/exFAT
/dev/sda3       263874558   312580095    24352769    5  Extended
/dev/sda4       102481920   263872511    80695296    7  HPFS/NTFS/exFAT
/dev/sda5       263874560   310505471    23315456   83  Linux
/dev/sda6       310507520   312580095     1036288   82  Linux swap / Solaris

Partition table entries are not in disk order

Disk /dev/sdc: 500.1 GB, 500107862016 bytes
255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x5822aaea

 Device Boot      Start         End      Blocks   Id  System
/dev/sdc1            2048   976769023   488383488    7  HPFS/NTFS/exFAT

The part below "Partition table entries are not in disk order" takes about 5 minutes to appear.


The outputs of ls /dev/ | grep sd before and after connecting the HDD:

before:

sda
sda1
sda2
sda3
sda4
sda5
sda6

,after:

sda
sda1
sda2
sda3
sda4
sda5
sda6
sdd
sdd1

The second output has the lines sdd and sdd1 different from the first one.


IT SHOWED THE FILES!!

The command sudo mount /dev/sdd1 /mnt worked after I typed in sudo fdisk -l!!! Thanks a million!! :) :)

7
  • Since you are sure, then here it is: please provide extra information.
    – January
    Jul 11, 2013 at 16:36
  • Can you assure that it is no hardware problem like a broken cable? Does it work on other computers? Also, please remove the device and start the program "terminal" and type "ls /dev/ | grep sd". Then do the same while the device is connected and switched on. Please copy everything from the terminal and edit it into your question.
    – verpfeilt
    Jul 11, 2013 at 16:36
  • my idea was that you tell me what you need to know, sry. I will edit the title. I did forget some basic information.
    – 842Mono
    Jul 12, 2013 at 17:06
  • For future searchers: make sure you try restarting your computer (that old classic) before trying anything fancy! I had this problem and a simple restart fixed it :)
    – user606179
    Dec 23, 2016 at 12:39
  • This was some old bug and I think it got fixed coz I don't get it on newer Ubuntus. Probably you got the fix in an update :D Anyway the solution doesn't do anything permanent. It was sort of a workaround @JoeRocc
    – 842Mono
    Dec 23, 2016 at 13:45

3 Answers 3

27

Okay here's what worked... (Here's a video explanation)


Firstly let's check if Ubuntu detects the device:

Disconnect your device then open a terminal and input ls /dev/ | grep sd and Enter. Now connect the device and input ls /dev/ | grep sd again and Enter. Now you should have two outputs. Compare them to each other.

You should find an extra line (or two) in the second output. Keep that extra line somewhere; we'll use it later.

If you can't find a difference then I don't think my solution will work for you but you can try. Probably you have a hardware problem.


(Here's the second part of the video demonstrating what's below)

Now input sudo fdisk -l in a terminal. You should see a large output.

Wait until the "prompt" (the line that looks like user@host:~$) appears again. It might take up to 5 minutes.

When the prompt appears again now you can now "mount" the device with this command:

sudo mount /dev/sdxn /mnt

Replace sdxn by the extra line you found when we did the first step.

(example: sudo mount /dev/sdb1 /mnt)

And you're done!



Summary: To mount the hard disk again later:

  • sudo fdisk -l
  • Wait
  • sudo mount /dev/sdxn /mnt
6
  • 2
    sdc and sdc1 were the new ones that appared when I typed "ls /dev/ | grep sd". I did the mount command and it said "mount: you must specify the filesystem type".
    – gogobebe2
    May 13, 2016 at 22:11
  • 5
    Same problem here, I got: mount: wrong fs type, bad option, bad superblock on /dev/sdb, missing codepage or helper program, or other error Oct 24, 2018 at 17:24
  • This is exactly the type of Q/A that is making me dizzy. First, selecting your own answer as "best answer", although month ago j0h gave a perfectly short answer containing all you'd need. Second, this question may have been asked 1000 times, and there are even more articles online, explaining linux' mount, which is basics. In sum, this is only noise, making it really hard to find answers for real issues (e.g. your device does not even show up in /dev/). PLEASE take your time searching and reading first, before you artificially increase your reputation score at the cost of such noise..
    – randmin
    Jan 27, 2021 at 11:01
  • 2
    @randmin This is a very old question. But here's what I remember. I did the digging, and I wrote this answer. It's more detailed than j0h's answer. You can read about "link only answers". Maybe j0h's answer is not link only, but it definitely relies on links. Moreover, Askubuntu, I believe, is not just for experts. It's made for all Ubuntu users who are facing trouble. I was quite inexperienced with Ubuntu back then. Also, if you feel that the question is a duplicate, you can mark duplicates. Also, this question specifically, I believe, was dealing with a bug that was fixed.
    – 842Mono
    Feb 5, 2021 at 0:43
  • @randmin To further support my claim which is that my answer is good, take a look at the votes. They are not mine. The votes mean that people find the answer helpful.
    – 842Mono
    Feb 5, 2021 at 0:46
5

You can look here to learn about detecting devices. Detect and mount devices

if the device is recognized, then you can try mounting the device. #mount /dev/sdb1 /home/user/someFolder

if you get errors, post them here. if you have LVM problems, you might find this helpful: http://pissedoffadmins.com/os/mount-unknown-filesystem-type-lvm2_member.html

0
0

It is simple. Follow these steps:

    fdisk -l

This will list out the partitions. Lets assume, your disc is "xxx"

pmount xxx /media/mydisc;

Your disk will be mounted at /media/mydisc directory.

If you want to unmount it,

umount /media/mydisc;
2
  • 1
    Should be mkdir -p /media/mydisc && mount xxx /media/mydisc
    – Zaz
    Dec 21, 2014 at 10:41
  • I would like to know the advantage of pmount, sounds interesting...
    – PJ Brunet
    Jun 27, 2020 at 21:25

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .